Warranty
Parts Finder Q offers a warranty for all types of parts in any condition. The warranty applies exclusively to purchases made directly through our website (partsfinderq.com). Please note that purchases made through third-party platforms like eBay or Amazon are not covered by this warranty.
Product Description
| Product Name | Engine Control Module (ECM) |
| Condition | Remanufactured |
| Brand | International® / Navistar® |
| Part Number | 1839368C1 |
| Vehicle Compatibility | |
|---|---|
| International 4300 / 4400 DuraStar | 2004–2007 (DT466 EGR with separate ECM and IDM) |
| IC Corporation CE school bus | 2004–2007 (DT466 EGR) |
| Engine Compatibility | |
| Engines | DT466 EGR (EPA04) |
Useful Information
Description and Purpose:
This is a remanufactured, genuine International® / Navistar® 1839368C1 Engine Control Module (ECM), sold as a single piece: the ECM box only. On the 2004–2006 DT466 with EGR, Navistar's "2-box" system bolts the ECM to the Injector Drive Module (IDM) on the driver side of the engine. This unit replaces the ECM half and bolts onto the IDM already on your engine.
The ECM holds the engine calibration and the vehicle parameters (VIN, engine serial number, rating, transmission type, miles, hours and fuel), and it is the only one of the two boxes that talks to a scan tool. It is used on International® 4300 and 4400 DuraStar trucks and IC CE school buses with the 2004–2006 DT466 EGR engine.
ECM Only vs. ECM/IDM Assembly:
- Included: the 1839368C1 ECM only.
- Not included: the IDM, the box that powers and fires the injectors. Your existing IDM stays on the engine.
- Choose this ECM when diagnosis points to the ECM and your IDM is good: ROM/RAM self-test codes 631/632, or VIN and parameter data lost again after reprogramming.
- Choose the complete assembly when IDM codes are present (523, 525, 533/534, 551–554 or injector-driver faults), when a 543 ECM/IDM communication fault can't be pinned to one box, or when the stack is damaged by oil or water.
Need both boxes? See the 1839368C1 & 1842443C92 ECM/IDM assembly.
Vehicle Fitment:
Match the number on your old ECM's label (1839368C1, seen with label number 5WY7194/01), or have a dealer look up the correct ECM by VIN.
Years and models are listed under Vehicle Compatibility, and engines under Engine Compatibility, in the table above.
- Not a fit: single-box DT466E/DT530E engines with no IDM (type I308; some 2004 model-year trucks still have it) and 2007-and-later MaxxForce DT engines with a SID 904 ECM label.
- Not confirmed: VT365 V8 and DT570 engines, although the 1839368C1 number has been seen on both. Check by VIN.
Common Symptoms and Trouble Codes:
- Lost ECM data: codes 141, 142 and 621 (factory default rating), VIN and engine serial number gone, miles, hours and fuel reset to 0, EFRC shows FFFF, the transmission defaults to manual and power drops (Navistar bulletin IK2600272). The usual cause is disconnecting the batteries less than 60 seconds after key-off; if data is lost again after reprogramming, suspect the ECM.
- Self-test and software: 631 / 632 (ROM / RAM self-test fault), 613 (ECM/IDM software not compatible), 614 (EFRC/ECM configuration mismatch), 623 (invalid EFRC), 664 (calibration level incompatible), 655 / 661 / 665 (parameter list incompatible or corrupt). 631/632 point to the ECM itself; for the rest, check the programming first.
- Communication and power: no scan-tool connection, 231 (ATA data link error), 626 (unexpected reset), 112 / 113 (battery voltage high / low).
- Common causes: failed battery-box "clean power" fuses feeding the ECM, IDM and TCM (Navistar bulletin IK1200261), a loose ECM plug (owner reports) and oil or water intrusion (repair shops).
- Can mimic a bad ECM: cam/crank position signal faults (codes 143–147) and power or ground problems. For a crank/no-start with no RPM on the scan tool, Navistar bulletin IK1201407 checks these before the module.
Installation Notes:
- Programming is required. Navistar's instruction is to program a replacement module to the VIN (IK1201407). Use an International® dealer or a shop with Navistar ServiceMaxx and NavKal.
- Program it bolted to your IDM: a replaced box is programmed with NavKal while both modules are connected. The 16-digit calibration reference covers both (first 8 digits ECM, last 8 IDM); mismatched software sets code 613.
- Before removal: if the old ECM still communicates, have its parameters saved as a template (IK2600256). Wait at least 60 seconds after key-off before disconnecting the batteries.
- Non-International chassis: programming is dealer-only through a case file that works only on that exact ECM (IK2600256); ask your dealer before ordering.
- Connector: the ECM X3 (6020) connector is white; release its center lock before separating it.
Manufacturer Information:
Genuine International® / Navistar® part. 1839368C1 is Navistar's ECM hardware number for the two-box ECM/IDM system of the 2004–2006 I6 diesel (engine type I313).
Warranty:
Parts Finder Q offers a 365-days warranty for all types of parts in any condition. The warranty applies exclusively to purchases made directly through our website (partsfinderq.com). Please note that purchases made through third-party platforms like eBay or Amazon are not covered by this warranty.
Questions & Answers
About Genuine International® / Navistar® ECM Only (No IDM) for DT466 EGR 1839368C1
Not sure it fits?
Send us your VIN — we'll confirm compatibility before you order.
Send your VIN Call +1 828-440-0199Which number on my old ECM should match?
The ECM label should read 1839368C1. Suffixes C2, C3, C4, C6 and C7 exist, but interchange is not confirmed, so match your label or confirm by VIN. Parts sellers cross-reference Navistar reman ECM 5012011R91 to 1839368C1, C2 and C7.
Does this 1839368C1 include the Injector Drive Module (IDM)?
No. It is the ECM only and bolts onto the IDM already on your engine. For both boxes, choose the 1839368C1 & 1842443C92 ECM/IDM assembly.
My old ECM says 1839368C1 but came off a VT365 V8 or a DT570. Will this one work?
Possibly, but this listing is described for the DT466 EGR and we have not confirmed those engines. Have a dealer check by VIN; programming to the VIN is required in every case.
Will this ECM run the truck as soon as it is bolted on?
No. It must be programmed to your VIN by an International® dealer or a shop with Navistar software. Bring the VIN, engine serial number, rating, transmission type and photos of your old labels.
Is there a core charge?
No. There is no core charge on 1839368C1 — you don't need to send your old part back.
How do I know the ECM failed and not the IDM?
ECM signs are codes 631/632, or VIN and mileage data lost again after reprogramming. IDM codes include 523, 525, 533/534 and 551–554. Code 543 (SID 155 FMI 7) is a fault between the boxes and doesn't show which one failed.
My scan tool can't talk to the engine and the truck is in limp mode. Is the ECM dead?
Not necessarily. Only the ECM talks to the scan tool, so a power, ground or data-link fault looks the same. Check ECM power and ground, the data link (code 231) and the clean-power fuses first.
Can a bad ECM keep a DT466 from cranking?
Possibly. Forum technicians report that the starter relay is grounded through the ECM; we have not confirmed this in Navistar documents. A verified check point is the battery-box clean-power fuses.
The cluster shows many codes and the engine won't run. Where do I start?
Read the engine codes with Navistar ServiceMaxx (J1708). With no RPM on the tachometer while cranking, follow Navistar's no-start bulletin IK1201407 first.
What warranty and shipping do you offer?
1839368C1 comes with a 365-day warranty. Orders placed before 7 PM EST ship the same business day, shipping is free on orders over $199, and local pickup is available at our South Carolina warehouse.
Not sure it fits?
Send us your VIN — we'll confirm compatibility before you order.
Send your VIN Call +1 828-440-0199Product reviews
Store reviews
What customers say about Parts Finder Q
4.7 · 110 store reviews across all parts
Installed and working
Installed and working perfectly
What we have here is a failure to communicate
Order number Q3793 was placed and confirmed on Wednesday, 21 Oct. The confirmation email said "We will notify you when it has been sent." When no word had been received in over a week, I sent emails on Thursday the 29th @ 12:05 & a second @ 16:43 to the partsfinderq.com support asking for shipper and tracking number. There was no response to either.On Friday the 30th, a request was sent for the same information thru the site's Order Status Inquiry form at about 12:30. Average response time was shown as "15 minutes". No reply as of two hours later.So, called @ 14:35. Although my transaction was found, its status was obviously unknown. A discount was offered (which was not applied) while I guess the elusive item was being searched for. Despite the assurance otherwise, no further Parts Finder Q correspondence was received for the rest of the day.Much later, an email notice from UPS suddenly appeared @ 20:01 - "Your package is on its way!" Magic.The item was delivered Tuesday, 3 Nov. So shipping took 4 days - over a weekend, but it hadn't even actually been sent until the 30th, 9 days after the order confirmation and my card being charged. The label wasn't even created until that Friday so the part appears to have not existed when ordered.The part itself appears very clean, so an extra star for that. But I neglected to ask whether it had actually been repaired/refurbished/tested. These have become very expensive since their failure rate is apparently high, and they're not made anymore.So two questions arise: 1) Does "In Stock" really mean "on the shelf", and 2) How many days does it take to locate and send an "In Stock" part after confirming an order? This unit is for a family car in nearly continuous use and the repair needs to be dovetailed. Not having any idea when, or even if, the order would arrive prevented that. I think you can do better.Edit 11 Nov 26:Parts Finder Q applied a discount, admittedly after my initial review mentioned it. This wasn't a necessary aspect of the transaction's follow-up, but it was volunteered and appreciated. Added a star with the caveat that future customers shouldn't need to make extra enquiries for an order to go smoothly.
Worked
Worked great
Correct part and it works
The part was correct, it was shipped fast and the Customer is happy and says his car is working fine . So far so good he said. Thank you.
2012 DODGE CHALLENGER ABS CONTROL
2012 DODGE CHALLENGER ABS CONTROL.
Satisfied customer
My part arrived ahead of time, it was the right part and the price was better than other sellers. Communication was also excellent. I will definitely order from them again
These guys are fantastic
These guys are fantastic. Have probably ordered a dozen modules by now for our shop and all work flawless. They will continue to get our business.
Perfect
Perfect, so happy I found it
Very happy.
Have ordered multiple items so far and very happy with quality. OEM new are unavailable and these guy came through big time!
The product was great
The product was great, finally got dodged, put it in and it’s working wonderfully thank you again for the experience and the quick responses.
excellant
excellant
Great part
Great part, had it installed, works like a charm









